Security "Secure Vent" Direct Vent Pipe



Lindemann Chimney Supply sells wholesale only  to the chimney and hearth industry.


SECURE VENT
Direct Vent Pipe



Compression fit with twist-lock design: inner flue has ultra tight, metal-to-metal conical seal; outer flue features compression fit.Three times tighter than industry standard.

Airtight laser weld construction on inner and outer casing
Tested with major direct-vent stove and insert manufacturers
Increases the performance of direct-vent appliances
Aluminized steel flue casing for superior strength and heat tolerance
Galvalume outer casing resists corrosion seven times longer than galvanized steel to ensure long-lasting aesthetic appeal
All black lengths and components painted with Forrest metallic black paint to match today's stoves
No unsightly lock seam, rivets or welds
Tested to ANSI Z21.88-2000 and CSA 2.33-2000
30-year limited warranty

DOWNLOADS:
SECURE VENT Direct Vent System is an airtight, leak-proof vent system for direct-vent gas-burning fireplaces and stoves. You'll love using this pipe; it removes the hassles of installing direct vent pipe. Totally airtight, Secure Vent requires no gaskets or silicone. It is laser welded inside and out, creating a finished "no seam" look because it has an aluminized steel inner liner. Twist lock, compression fitting goes together easily - and comes apart easily. 4" interior and 6-5/8" exterior dimensions. 30 year limited warranty.

TYPICAL INSTALLATIONS
These diagrams will help you plan your installation. Components listed in the diagram may be found below.
Vertical Installation
   1. Vertical Term. Cap
   2. Storm Collar
   3. Flashing
   4. Roof Support
   5. Pipe Length
   6. Attic Insulation Shield
   7. Firestop
   8. Decorative Black Plate
   9. Pipe (Black)
10. Insulation

Vertical (2 floors)
1. Pipe (Black)
2. Decorative Black Plate
3. Floor Support
4. 45 deg Elbow
5. Pipe Length
6. Adj. Wall Band
7. Firestop
8. Insulation
Vertical Cathedral
1. Vertical Term. Cap
2. Pipe (galv)
3. Storm Collar
4. Flashing
5. Collar for Decorative Square Cathedral Support
6. Adj. Decorative Square Cathedral Support
7. Pipe (Black)
8. Insulation

Horizontal Termination
1. Horizontal Term. Cap
2. Wall Radiation Shield
3. Decorative Black Plate
4. Pipe Length (black)
5. 90 deg. elbow (blk)
6. Concrete

Horizontal Snorkel Termination
1. Snorkel Term. Cap
2. Firestop
3. Pipe Length
4. Drain
5. Tar
6. Concrete

Secure Vent Pipe
Black pipe is used for interior application where the pipe will be visible. Galvalume finish pipe is used inside where it will not be seen, or for components that will be exposed to the outdoors. Adjustable length pipes slip to allow length adjustment without cutting.
Black
Order #
Galvalume
Order #
 6" length
250614
250604
 6" adjustable length
250314
251304
12" length
251214
251204
12" adjustable length
251314
250304
24" length
252414
252404
36" length
253614
253604
48" length
244814
254804
Elbows
feature a swivel design that allows the elbow to be turned after it is locked onto the length.
45 Degree Elbow
254514
254504
90 Degree Elbow
259014
259004

Components & Accessories
Description
Order #
Adjustable Square Ceiling Support
Decorative black box used in cathedral ceiling applications. Includes tightening collar and adjustable framing arms. Framing arms are adjustable from 1" to 7-3/4".

Needs the collar #254314 shown below.
254304

Collar for Decorative Square Cathedral Support
This collar is to be installed on the adjustable square cathedral support. It prevents insulation from seeping between the vent and the support.
254314
Decorative Black Plate
Used for horizontal, through-the-wall installations. Also used as a decorative ceiling support.
254404
Adjustable Wall Band
Serves to stabilize the vent while providing the required clearances.
250404
Roof Support
Attaches to the roof structure. Supports the vent in vertical applications.
250204
Universal Support
Used to support pipe in offsets.
Measures 19-5/16" long.
254204
Floor Support
Used in vertical installation when the vent runs through a floor. Maintains a 1" clearance from combustibles. The tightening collar is locked around the vent, secured by self tapping screws that rest on the plate. Can be screwed or nailed to the floor.
254604
Roof Brace
Installed when the vent height is 5' or more above the roof or when the vent is exposed to high winds. Supplied with a tightening collar and adjustable legs. Legs adjust from 60" to 115".
253004
Firestop
Protects surrounding materials when vent passes through the ceiling.
256004
Attic Radiation Shield
Cone shaped component is used when te vent passes through an attic. Prevents insulation from seeping between the vent and the firestop while maintaining 1" clearance from surrounding combustible material. 11" overall height.
256204
Wall Radiation Shield
Protects surrounding combustible materials when vent passes through the wall. Comes in two pieces that slide together.
256304
Roof Flashing
Needed for vertical installations. Seals the vent  pipe where it protrudes from a flat or sloped roof. Includes storm collar.
Flat Roof Flashing
257004
Flashing for 1/12 to 7/12 Roof Pitch
257104
Flashing for 8/12 to 12/12 Roof Pitch
257204
Storm Collar
Fits over flashings and provides a watertight seal. Collar is included with each roof flashing.
258004
Vertical Termination Cap
Cap used on vents exiting through the roof. Suitable for high-wind applications.
259104
Horizontal Termination Cap
Cap used on vents exiting through a wall
259204
Snorkel Termination Cap
Cap used on vents exiting through a wall when exit point is too close to the ground. Available in 2 sizes.
14" tall Snorkel
259304
36" tall Snorkel
259404
Restrictor Disc
Restricts incoming combustion air. Always refer to the appliance manufacturer's installation manual before use.
258204
Vinyl Siding Shield
This shield should be installed with horizontal termination; protects vinyl siding from damage and discoloration from exiting fume & heat.
258104
Direct Vent Sealant Tube
255200



Copyright Lindemann Chimney Supply 2005